Fix My Beep logo Fix My Beep Blog
Download on the App Store Get it on Google Play fixmybeep.com
Boilers

Viessmann Boiler F07 Error Code: What It Means and How to Fix It

Fix My Beep
By Phil Calver · Fix My Beep Editorial Team Published July 7, 2026 · Last reviewed July 7, 2026
🚨 WARNING: Never attempt DIY repairs on gas boilers or gas appliances.This is illegal without Gas Safe registration and potentially fatal. Call a Gas Safe registered engineer.

Boiler

F07

The F07 error code on a Viessmann boiler indicates a fault with the flue gas temperature sensor, and while it won’t always leave you without heating immediately, it’s a fault that needs prompt attention to keep your boiler running safely and efficiently.

What does this error mean?

The F07 code tells you that your boiler’s flue gas temperature sensor has detected an abnormal reading — either too high, too low, or an implausible signal that doesn’t match the boiler’s operating conditions. Viessmann boilers use this sensor to monitor the temperature of exhaust gases leaving through the flue; if readings fall outside safe parameters, the boiler locks out to prevent damage or a dangerous situation. In plain terms, the boiler thinks something is wrong with how hot the outgoing gases are, and it’s refusing to fire until that’s resolved.

💰

Est. repair cost

£150–£350 for sensor replacement by a Gas Safe engineer; no cost-effective DIY option for this repair

🔍 Likely causes

Faulty or failed flue gas temperature sensor (the most common cause — sensors degrade over time)Damaged or corroded wiring to the flue gas temperature sensor, causing an intermittent or broken signalBlocked or partially obstructed flue outlet, causing exhaust gases to back up and overheatCombustion problems (incorrect air-to-gas ratio) causing flue gases to run hotter than normalA failing heat exchanger that is running inefficiently and pushing excessive heat into the flueA temporary sensor glitch triggered by a power fluctuation or brief operating anomaly

🛠️ Step-by-step fix

1

Step 1 — Reset the boiler: Press and hold the reset button on your Viessmann boiler for 3–5 seconds. Many F07 faults caused by a temporary glitch will clear immediately. If the boiler fires up and runs normally for a full heating cycle without the code returning, monitor it for 24 hours.

2

Step 2 — Check your flue outlet externally: Go outside and visually inspect the flue terminal (the pipe or grille on your external wall or roof). Make sure it isn’t blocked by debris, a bird’s nest, ice, or overgrown vegetation. Do not attempt to access the flue internally.

3

Step 3 — Check for recent power issues: If your home recently had a power cut or surge, the fault may be a false trigger. Reset once more and observe. If the code returns within an hour of firing, stop here.

4

Step 4 — Do not attempt further DIY: The flue gas temperature sensor is an internal gas appliance component. Replacing it, testing it with a multimeter, or inspecting internal flue connections requires working on a live gas appliance — this is illegal for unqualified individuals under UK Gas Safety (Installation and Use) Regulations 1998. Call a Gas Safe registered engineer.

5

Step 5 — Note the pattern: Before calling an engineer, make a note of when the fault appears (cold start, mid-cycle, after long runs), how often it resets successfully, and whether you’ve noticed any unusual smells or sounds. This information helps the engineer diagnose the fault faster.

📞 When to call a professional

Call a Gas Safe registered engineer if the F07 code returns after a reset, if the boiler won’t reset at all, or if you notice any smell of gas, unusual noises, or visible soot around the boiler or flue. Tell the engineer: ‘My Viessmann boiler is showing an F07 fault code — I believe it’s related to the flue gas temperature sensor.’ This gives them a clear starting point and ensures they bring the right parts.

⚖️ Repair or replace?

A flue gas temperature sensor replacement on a Viessmann boiler typically costs £150–£350 including parts and labour, depending on your boiler model and engineer’s rates. If your boiler is under 10 years old, repair is almost always the right call — Viessmann boilers are well-built and worth maintaining. If the boiler is over 15 years old and this is one of several recent faults, get a quote for a new boiler alongside the repair cost; a new A-rated condensing boiler starts around £1,800–£2,500 installed.

⚠️ This guide is for informational purposes only and does not constitute professional repair advice. Always consult a qualified engineer for gas appliances. Gas appliance repairs must only be carried out by a Gas Safe registered engineer — it is illegal for unqualified persons to work on gas appliances in the UK. Repair costs are estimates based on typical UK market rates and may vary significantly. Fix My Beep and Rosetta Software Limited accept no liability for any loss, damage, injury or death resulting from following guidance on this website. Read our full disclaimer →

Get an instant AI diagnosis

Download Fix My Beep — free on iOS. Point your phone at any error code and get a step-by-step fix in seconds.

Download on the App Store Get it on Google Play
🌐 Visit fixmybeep.com

Related Error Code Guides

Boilers

Glow-worm Boiler E11 Error Code: What It Means and What to Do

The E11 error code on a Glow-worm boiler indicates a flame detection fault —…

Boilers

Viessmann Boiler F10 Error Code: What It Means and How to Fix It

The F10 error code on a Viessmann boiler indicates a flow temperature sensor fault…

Boilers

Baxi Boiler E160 Error Code: What It Means and How to Fix It

The E160 error code on a Baxi boiler indicates a fan or air pressure…

Boilers

Viessmann Boiler E10 Error Code: What It Means and How to Fix It

The E10 error code on a Viessmann boiler indicates a problem with the boiler's…

Fix My Beep

Fix My Beep Editorial Team

Fix My Beep is an AI-powered appliance diagnostic platform developed by Rosetta Software Limited. Our error code guides are generated using AI and reviewed by our editorial team to ensure accuracy and safety. Always consult a qualified engineer for safety-critical repairs, especially gas appliances. Learn more about us.

Fix My Beep

Fix My Beep App

Instant AI appliance diagnosis. Free on iOS & Android.

Download on the App Store Get it on Google Play fixmybeep.com

Browse by Appliance

  • Washing Machines
  • Dishwashers
  • Boilers
  • Ovens
  • Fridges
  • Tumble Dryers
  • Air Fryers

Recent Posts

  • Alpha Boiler F12 Error Code: What It Means and How to Fix It
  • AEG Dishwasher E8 Error Code: What It Means and How to Fix It
  • Siemens Tumble Dryer F16 Error Code: What It Means and How to Fix It
  • Candy Oven F7 Error Code: What It Means and How to Fix It
  • Miele Oven F7 Error Code: What It Means and How to Fix It

Recent Comments

No comments to show.

Archives

  • July 2026
  • June 2026

Categories

  • Air Fryers
  • Boilers
  • Cookers
  • Dishwashers
  • Freezers
  • Fridges
  • Ovens
  • Tumble Dryers
  • Washing Machines
Fix My Beep logo Fix My Beep

AI-powered appliance error code diagnosis. Decode every beep, flash, and fault code.

Appliances

  • Washing Machines
  • Dishwashers
  • Boilers
  • Ovens
  • Fridges
  • Tumble Dryers
  • Air Fryers

Get the App

  • Download on iOS
  • Get it on Google Play
  • Visit fixmybeep.com
© 2026 Fix My Beep. All rights reserved. · Disclaimer
Fix My Beep is a product of Rosetta Software Limited
Registered in England & Wales — Company No. 05930333
Registered office: 3 First Floor, Hornton Place, London, England, W8 4LZ
Download on the App Store Get it on Google Play
⚠️ All information on this site is generated by AI and provided for guidance only. Use at your own risk. Always consult a qualified engineer for safety-critical repairs. Read our full disclaimer.